Aero parts for your car

Splitters, skirts and diffusers
cut for your car.

Pick your car, design the parts in 3D, check a thin fit sample on the car if you want, then get the real parts. No CAD and no guesswork.

  • 33 part types
  • 72 cars, trucks and SUVs in the list
  • Optional fit sample before anything is cut

Step 1

Pick your car

Tell us about your car

We start from a typical body of its style. Design right away; before ordering, you take a few tape measurements (about 10 minutes) and a fit sample is checked on the car.

Know some sizes? Add them (optional)

From the owner's manual or a spec sheet. Anything left empty uses the typical value for the body style.

How it works

From your car to fitted parts

Pick your car

Search by make, model or year. Not listed? Describe it and take a few tape measurements.

Design it in 3D

Add parts, set the sizes and the material. Every fit check runs as you go.

Fit sample, if you want one

A thin plastic copy of the main pieces, cut first. Hold it on the car and tell us it fits. Or skip it and order the parts.

Get the real parts

Cut from aluminum, ACM, plywood, plastic or carbon, with the hardware list and install steps.

Parts

What you can make

Front

Front splitter

Flat plate under the front bumper, following its exact shape, with support rods and splice plates.

ACM aluminum composite · ABS plastic · Baltic birch plywood · 6061 aluminum · 5052 aluminum · Carbon fiber · HDPE marine board

Design it

Chin lip

Narrow flexible blade along the bumper lip: the street-friendly splitter.

ABS plastic · HDPE marine board · ACM aluminum composite

Design it

Splitter end plates (air dams)

Vertical plates at the splitter ends that seal the air under the car.

ACM aluminum composite · Carbon fiber · Carbon fiber, 0.118" (3 mm) · 5052 aluminum · ABS plastic

Design it

Canards (dive planes)

Small flat wings on the bumper corners, cut to follow the corner shape.

Carbon fiber · Carbon fiber, 0.118" (3 mm) · ABS plastic · 5052 aluminum · ACM aluminum composite

Design it

Front undertray

Flat panel from the bumper back to the subframe: a smooth floor under the engine bay.

ABS plastic · ACM aluminum composite · HDPE marine board · 5052 aluminum · Baltic birch plywood

Design it

Front air dam (valance)

Vertical blade hanging under the front bumper, cut in straight sections that follow its curve. Cuts lift and drag on trucks, SUVs and vans.

ABS plastic · HDPE marine board · ACM aluminum composite · 5052 aluminum

Design it

Front tyre spats (wheel deflectors)

Small vertical plates just ahead of the front tyres that turn the air round them. Left and right.

ABS plastic · HDPE marine board · ACM aluminum composite · 5052 aluminum

Design it

Radiator cooling duct plates

Side plates and a floor that seal the gap between the bumper opening and the radiator, so all the air goes through it.

ACM aluminum composite · ABS plastic · 5052 aluminum

Design it

Brake cooling inlet plates

Flat plates for a bumper or fog-light opening with a round spigot hole for brake cooling hose. Left and right.

5052 aluminum · ABS plastic · ACM aluminum composite · Carbon fiber, 0.118" (3 mm)

Design it

Licence plate relocation bracket

Bent bracket that moves the front plate off the splitter or air dam: to the side, or onto a bumper bolt.

5052 aluminum · Mild steel · 304 stainless steel

Design it

Side

Side skirt extensions

Flat blades under the rockers that keep air from rolling under the car. Left and right.

ABS plastic · ACM aluminum composite · HDPE marine board · Carbon fiber · 6061 aluminum · 5052 aluminum

Design it

Side skirt winglets

Small vertical fins hanging under the rear end of each side skirt, angled to push air out past the rear tyres. Left and right.

ABS plastic · Carbon fiber · Carbon fiber, 0.118" (3 mm) · ACM aluminum composite · 5052 aluminum

Design it

Mud flaps

Rally-style flaps behind the wheels, in HDPE or UHMW.

HDPE marine board · UHMW plastic · ABS plastic

Design it

Flat floor

Flat floor panel

Flat panel under the middle of the car, between the front undertray and the diffuser.

ABS plastic · ACM aluminum composite · 5052 aluminum · HDPE marine board

Design it

Rear

Rear diffuser

Panel under the rear bumper with slot-in strakes. Exhaust tips get heat-cleared notches.

ACM aluminum composite · ABS plastic · 5052 aluminum · Carbon fiber · 6061 aluminum

Design it

Rear valance (bumper skirt)

Vertical blade under the rear bumper, in straight sections, notched round the exhaust tips.

ABS plastic · HDPE marine board · ACM aluminum composite · 5052 aluminum

Design it

Ducktail (trunk lip spoiler)

Bent aluminum lip along the rear edge of the trunk lid.

5052 aluminum

Design it

Flat-plate rear wing

A flat aluminum wing plate with a bent gurney on its trailing edge, for the wing uprights.

5052 aluminum

Design it

Wing end plates

Replacement end plates for an existing rear wing.

Carbon fiber · Carbon fiber, 0.118" (3 mm) · 5052 aluminum · ACM aluminum composite

Design it

Wing uprights

Flat aluminum uprights (standard or swan-neck) for a rear wing.

6061 aluminum · 5052 aluminum

Design it

Wing mount backing plates

Plates that go inside the trunk lid (and optionally under each upright foot) to spread the wing load.

5052 aluminum · Mild steel

Design it

Gurney flap

Bent aluminum strip on the trailing edge of a wing or spoiler.

5052 aluminum · 304 stainless steel

Design it

Wicker bill

Angled aluminum strip riveted on top of a spoiler's or ducktail's trailing edge: a small, adjustable-feel gurney.

5052 aluminum · 304 stainless steel

Design it

Tailgate spoiler

Bent aluminum lip along the top of a pickup's tailgate that tidies the air off the bed.

5052 aluminum

Design it

Roof

Roof spoiler

Bent aluminum spoiler at the back edge of the roof: SUVs, vans, hatchbacks and truck cabs.

5052 aluminum

Design it

Roof rack wind fairing

Flat fairing on the front bar of a roof rack that cuts wind noise and drag. Cars, SUVs, trucks and vans.

ABS plastic · ACM aluminum composite · 5052 aluminum

Design it

Underbody protection

Engine skid plate

Protects the oil pan and front of the engine; ramps up to the front crossmember when the mounts are higher there.

5052 aluminum · Mild steel · UHMW plastic · HDPE marine board

Design it

Transmission skid plate

Covers the transmission between the frame rails.

5052 aluminum · Mild steel · UHMW plastic · HDPE marine board

Design it

Transfer case skid plate

Covers the transfer case on 4x4s.

5052 aluminum · Mild steel · UHMW plastic · HDPE marine board

Design it

Fuel tank skid plate

Covers the fuel tank.

5052 aluminum · Mild steel · UHMW plastic · HDPE marine board

Design it

Rear differential skid plate

Covers the rear differential.

5052 aluminum · Mild steel · UHMW plastic · HDPE marine board

Design it

Control arm skids

Small plates under the lower control arms. Left and right.

5052 aluminum · Mild steel · UHMW plastic · HDPE marine board

Design it

Front bumper skid plate

Sloped plate under a truck, SUV or van front bumper that guards the bumper's underside and smooths the air under it.

5052 aluminum · Mild steel · HDPE marine board · UHMW plastic

Design it

The fit

How we make sure it fits

Estimated from published dimensions

Every car in the list starts from its published size: wheelbase, track, overhangs and ground clearance, with the sources shown. That sets the shape of each part.

A few tape measurements, if you like

Optional for listed cars: about 10 minutes with a tape measure, each step with a drawing. They make the first cut spot on. Cars that aren’t listed need them.

An optional fit sample

Want to see it on the car first? The main pieces are cut in thin polypropylene and shipped to you. Tape them together, hold them on the car and confirm, then the real parts are cut. Or skip it and order the parts straight away.

FAQ

Questions, answered

Do I have to measure my car?

Not if it is in our list. The shape comes from published dimensions; to be sure before the real parts are cut, order the fit sample, so a wrong guess costs a thin plastic sheet, not a splitter. A few tape measurements make it right first time.

My car isn’t listed. Can I still order?

Yes. Pick the body style, enter the make, model and year, and take the tape measurements: about 10 minutes. The parts are cut from those; a fit sample first is recommended.

What is the fit sample?

An optional, paid check: a thin polypropylene copy of each main piece, cut first and shipped to you. Tape the tiles together on their marks, hold them under the car, turn the wheels lock to lock, and tell us if it fits. You can also skip it and order the parts directly.

What do the parts cost?

The designer shows an estimate as you go. We confirm the price by email within 1–2 business days; nothing is cut or charged until you approve it.

Is it street legal?

Ground clearance and overhang rules vary by state and by event. The designer flags anything lower than the clearance you set (3 in by default); the rules where you drive are your call.

I run a shop. Is there more?

Yes: the shop tools add precision measuring with printed marker mats for unusual or modified cars, saved kits per customer and the full cut files.

Fitting aero for customers?

Shop tools add precision measuring for unusual or modified cars, with printed marker mats.

Aero for shops